In this guide, we will step-by-step guide you to use video camera IMX708 on SP7350 platforms.
Contents
| Table of Contents |
|---|
1 IMX708
...
Specification
Back-illuminated and stacked CMOS 12-megapixel image sensor
Pixel Size: 1.4 x 1.4 μm
HorizoHorizontal/vertical: 4608 × 2592 pixels
Sensor size: 7.4mm sensor diagonal
Optical size: 1/2.43"
Maximum exposure times (seconds): 112
HDR mode (up to 3 megapixel output)
video modes: 2304 × 1296p56, 2304 × 1296p30 HDR, 1536 × 864p120
2 Setup
2.1 Enable IMX708 in
...
Linux Kernel Configuration
1 Enter the kernel configuration by running the following command in the top directory of project.
| Code Block | ||
|---|---|---|
| ||
make kconfig |
2 Selects submenussub-menus: Device Drivers>Multimedia support>Media ancillary drivers>Camera sensor devices
...
3 Select Sony IMX708 sensor support and pressing <Y> inlucdesincludes. Then save and exit.
2.2 Modify
...
Device-tree
...
Source
Device-tree source files of SP7350 are located in linux/kernel/arch/arm64/boot/dts/sunplus/.
...
Modify device tree source file to define IMX708 source for driver
2.2.1 Using SP7350 MIPI
...
/CSI-RX4
Open IMX708_IN4 macro to add IMX708 node and link mipicsirx4.
2.2.2 Using SP7350
...
Other MIPI
...
/CSI-RX
Define IMX708 node in i2c node:
...
| Code Block |
|---|
mipicsirx: csirx@f8005480 {
port@0 {
reg = <0>;
/* MIPI CSI-2 bus endpoint */
csi_ep: endpoint {
remote-endpoint = <&imx708_ep>;
bus-type = <4>;
clock-lanes = <0>;
data-lanes = <1 2>;
};
}; |
2.3 Compile and
...
Burn
2.4 Connect
...
Sensor Module
Using C3V-W board MIPI-CSI-RX4, as follows：
...
2.5 Check
After the burning is completed, start the board. The system should print the following information through the serial port.
...
| Code Block |
|---|
root@dbv3:~# ls /dev/video0 /dev/video0 |
3 Test
3.1
...
v4l2-ctl
...
Command
This command is used to control V4L2 devices from the command line. It allows you to query device capabilities, set device parameters, and capture video and still image.
...
| Code Block |
|---|
root@dbv3:~# v4l2-ctl --all --device /dev/video0
Driver Info:
Driver name : sp_vin
Card type : SP_VIN
Bus info : platform:f8005980.video
Driver version : 5.10.201
Capabilities : 0xa5200001
Video Capture
Read/Write
Streaming
Extended Pix Format
Device Capabilities
Device Caps : 0x25200001
Video Capture
Read/Write
Streaming
Extended Pix Format
Media Driver Info:
Driver name : sp_vin
Model : sunplus,sp7350-vin
Serial :
Bus info : platform:f8005980.video
Media version : 5.10.201
Hardware revision: 0x00000000 (0)
Driver version : 5.10.201
Entity Info:
ID : 16
Name : VIN8 output
Type : V4L2 I/O
Pad : 0: Sink
Priority: 2
Video input : 0 (VIN8 output: ok)
Format Video Capture:
Width/Height : 1536/864
Pixel Format : 'RG10' (10-bit Bayer RGRG/GBGB)
Field : None
Bytes per Line : 3072
Size Image : 2654208
Colorspace : Raw
Transfer Function : None
YCbCr/HSV Encoding: ITU-R 601
Quantization : Full Range
Flags :
User Controls
exposure 0x00980911 (int) : min=1 max=2602 step=1 default=1600 value=1600
horizontal_flip 0x00980914 (bool) : default=0 value=0 flags=modify-layout
vertical_flip 0x00980915 (bool) : default=0 value=0 flags=modify-layout
alpha_component 0x00980929 (int) : min=0 max=255 step=1 default=255 value=255
Camera Controls
wide_dynamic_range 0x009a0915 (bool) : default=0 value=0 flags=modify-layout
Image Source Controls
vertical_blanking 0x009e0901 (int) : min=40 max=8387616 step=1 default=2755 value=58
horizontal_blanking 0x009e0902 (int) : min=3680 max=3680 step=1 default=3680 value=3680 flags=read-only
analogue_gain 0x009e0903 (int) : min=112 max=960 step=1 default=112 value=112
red_pixel_value 0x009e0904 (int) : min=0 max=4095 step=1 default=4095 value=4095
green_red_pixel_value 0x009e0905 (int) : min=0 max=4095 step=1 default=4095 value=4095
blue_pixel_value 0x009e0906 (int) : min=0 max=4095 step=1 default=4095 value=4095
green_blue_pixel_value 0x009e0907 (int) : min=0 max=4095 step=1 default=4095 value=4095
notify_gains 0x009e0909 (u32) : min=1 max=65535 step=1 default=256 [4] flags=has-payload
Image Processing Controls
link_frequency 0x009f0901 (intmenu): min=0 max=0 default=0 value=0 flags=read-only
pixel_rate 0x009f0902 (int64) : min=566400000 max=566400000 step=1 default=566400000 value=566400000 flags=read-only
test_pattern 0x009f0903 (menu) : min=0 max=4 default=0 value=0
digital_gain 0x009f0905 (int) : min=256 max=65535 step=1 default=256 value=256 |
3.2 Capture
...
Image
3.2.1 Config
...
Video Device
Use v4l2-ctl -d /dev/video0 --set-ctrl params=value setting device controls.
...
Change image brightness by changing the exposure, analogue_gain and digital_gain.
3.2.2 Capture
Use v4l2-ctl --list-formats-ext --device /dev/video0 querying device video format.
...
After executing the capture command, the stream data is written to /home/root/imx708.raw.
3.3 Display
...
Image Raw Data
3.3.1 Download and
...
Install Raw Image Viewer
Download raw image viewer from PixelViewer | Carina Studio. And PixelViewer is an open source project based cross-platform image which viewer supports reading raw Luminance/YUV/RGB/ARGB/Bayer pixels data from file and rendering it.
3.3.2 Use
...
PixelViewer to Open Image
...
Config render params by 3.2.2 v4l2-ctl capture command
...
3.3 HDR
Enable HDR
| Code Block |
|---|
v4l2-ctl -d /dev/video0 --set-ctrl wide_dynamic_range=1 |
...