Page Comparison

Case download:
fbio_selftest.zip

1 Design Brief

The SP7021 SOC platform LOOPBACK self-test experiment is mainly used to test the reliability of the SOC platform connection. The design of the FBIO Bus Bridge is placed on the FPGA daughter board. The Plus1 chip reads and writes the FBIO Bus Bridge to realize the reliability test of the connection between the Plus1 chip and the FPGA daughter board pin .

...

The SP7021 SOC platform self-test experiment only needs to connect the axi_m and axi_s 64bit axim and axis bus interfaces of the FBIO Wrapper Bus Bridge together, and do the corresponding address mapping. That is, the access to the FBIO Bus Bridge start address 0x70000000 is mapped to the access to the DRAM start address 0x00000000 in the Plus1 SP7021 chip ;As shown below:

...

This This experiment uses the FPGA daughter board supporting the Plus1 7021 SP7021 practice platform to complete the relevant experiments. The development tool of the FPGA daughter board uses Xilinx's Vivado integrated development environment (version number 2018.3); in order to facilitate the connection of the user's own verification IP to the SOC system Verification, this experiment provides the corresponding design reference basic files, as follows

...

The corresponding connection between the design case and the pin connection of the SP7021 motherboard and FPGA daughter board is shown in the following table: 1: U20B on the motherboard is connected to J2 of the FPGA daughter board (Pin pin corresponding, such as 1-51 ...), providing the data transmission channel between the Plus1 main chip on the motherboard and the FPGAImage Removed

...

Design Demo	FPGA daughter board			SP7021 mother board
fbio_selftest	J2		U1E	U20B
Top Port Name	Schematic Name		FPGA I/O	Schematic Name
	1	GND		51	GND
	2	GND		52	GND
FPGA_PAD[0]	3	B34_L24_N	T8	53	FBIO_PAD_0
FPGA_PAD[43]	4	B34_L24_P	R8	54	FBIO_PAD_1
	5	VIN		55	VCC(3.3V)
	6	VCCIO34		56	VCC(3.3V)
FPGA_PAD[1]	7	B34_L21_N	V9	57	FBIO_PAD_2
FPGA_PAD[42]	8	B34_L21_P	U9	58	FBIO_PAD_3
FPGA_PAD[2]	9	B34_L18_N	N6	59	FBIO_PAD_4
FPGA_PAD[41]	10	B34_L18_P	M6	60	FBIO_PAD_5
FPGA_PAD[3]	11	B34_L22_N	U6	61	FBIO_PAD_6
FPGA_PAD[40]	12	B34_L22_P	U7	62	FBIO_PAD_7
FPGA_PAD[4]	13	B34_L20_N	V6	63	FBIO_PAD_8
FPGA_PAD[39]	14	B34_L20_P	V7	64	FBIO_PAD_9
FPGA_PAD[5]	15	B34_L23_N	T6	65	FBIO_PAD_10
FPGA_PAD[38]	16	B34_L23_P	R7	66	FBIO_PAD_11
FPGA_PAD[6]	17	B34_L10_N	V4	67	FBIO_PAD_12
FPGA_PAD[37]	18	B34_L10_P	V5	68	FBIO_PAD_13
FPGA_PAD[7]	19	B34_L19_P	R6	69	FBIO_PAD_14
FPGA_PAD[36]	20	B34_L19_N	R5	70	FBIO_PAD_15
FPGA_PAD[8]	21	B34_L8_P	U4	71	FBIO_PAD_16
FPGA_PAD[35]	22	B34_L8_N	U3	72	FBIO_TCLK
FPGA_PAD[9]	23	B34_L9_N	V2	73	FBIO_RCLK
FPGA_PAD[34]	24	B34_L9_P	U2	74	FBIO_PAD_17
FPGA_PAD[10]	25	B34_L7_N	V1	75	FBIO_PAD_18
FPGA_PAD[33]	26	B34_L7_P	U1	76	FBIO_PAD_19
FPGA_PAD[11]	27	B34_L13_P	N5	77	FBIO_PAD_20
FPGA_PAD[32]	28	B34_L13_N	P5	78	FBIO_PAD_21
FPGA_PAD[12]	29	B34_L12_P	T5	79	FBIO_PAD_22
FPGA_PAD[31]	30	B34_L12_N	T4	80	FBIO_PAD_23
FPGA_PAD[13]	31	B34_L11_N	T3	81	FBIO_PAD_24
FPGA_PAD[30]	32	B34_L11_P	R3	82	FBIO_PAD_25
FPGA_PAD[29]	33	B34_L14_P	P4	83	FBIO_PAD_26
FPGA_PAD[28]	34	B34_L14_N	P3	84	FBIO_PAD_27
FPGA_PAD[14]	35	B34_L16_N	N4	85	FBIO_PAD_28
FPGA_PAD[27]	36	B34_L16_P	M4	86	FBIO_PAD_29
FPGA_PAD[15]	37	B34_L17_N	T1	87	FBIO_PAD_30
FPGA_PAD[26]	38	B34_L17_P	R1	88	FBIO_PAD_31
FPGA_PAD[16]	39	B34_L15_N	R2	89	FBIO_PAD_32
FPGA_PAD[25]	40	B34_L15_P	P2	90	FBIO_PAD_33
FPGA_PAD[17]	41	B34_L3_N	N1	91	FBIO_PAD_34
FPGA_PAD[24]	42	B34_L3_P	N2	92	FBIO_PAD_35
FPGA_PAD[18]	43	B34_L1_N	M1	93	FBIO_PAD_RSTB
FPGA_PAD[23]	44	B34_L1_P	L1	94	EXT0_INT
	45	VCCIO34		95	VCC(3.3V)
	46	VIN		96	VCC(3.3V)
FPGA_PAD[19]	47	B34_L4_P	M3	97	EXT1_INT
FPGA_PAD[20]	48	B34_L4_N	M2	98
	49	GND		99	GND
	50	GND		100	GND

...

Next, you need to copy all the files and folders under the installation directory \SP7021\example\ fbio_selftest to the fbio_selftest project directory built above (the path is: installation directory \SP7021\ workspace\fbio_selftest\), the file with the same name is selected to be overwritten, so SP7021 The the program code main.c required for SP7021 SOC platform self-test design practice; put it in the following path:

1） Install main.c in In the install directory \SP7021\workspace\fbio_selftest\ foldermain.c

Finally, as shown in the figure below, select the red box 1 with the mouse, then click the right mouse button to display the drop-down menu, and then select the red box 2, refresh the copy action just now, so that the file just copied can be displayed in the IDE environment.

...

The first for loop uses fbio to write to the DRAM address space 1 to 200 of the Plus1 chip;

The first second for loop reads the DRAM address space 1 to 100 of the Plus1 chip through fbio module; compares the read content with the written content, and if it is different, prints the Error message;

...

Versions Compared

Old Version 6

New Version Current

Key

1 Design Brief