SNNF demo includes the following model samples
yolov8n_pose_opti;
yolov8n_segment_opti;
yolov8n_detection_opti;
det_10g + w600k_r50; (face match)
lightFace;
age;
yolov8n_detection_opti + humanAttr;
Human tracking;
Human falling detection;
OCRDet + OCRCls + OCRRec;
If you want to see the demo's effects more quickly, please refer to SNNF Demo Introduction.
If you want to compile the SNNF demo, please read this document carefully.
HW Environment
Camera
The SNNF demo supports obtaining input data through a camera or a video file. The camera can be connected through MIPI or USB.
MIPI
Currently, the sensor we support for the MIPI interface is OV5640. The sensor needs to be connected to MIPI-RX4_2D on the platform, the MIPI Sensor interface as shown in the diagram above.
If you plan to use it, you need to make the following modifications before building the C3V image.
modify the linux/kernel/arch/arm64/boot/dts/sunplus/sp7350-dm.dts，enable OV5640_IN4
@@ -19,7 +19,7 @@ //#define IMX708_IN5 //#define OV5640_IN2 //#define OV5640_IN3 -//#define OV5640_IN4 +#define OV5640_IN4 //#define OV5640_IN5 //#define OV5647_IN2 //#define OV5647_IN3
To improve the speed of reading data from the sensor, you can make the following settings:
Permanently modification
modify the linux/kernel/drivers/media/common/videobuf2/videobuf2-dma-contig.c,
set the remap to true.
@@ -22,7 +22,7 @@
#include <media/videobuf2-dma-contig.h>
#include <media/videobuf2-memops.h>
#if defined(CONFIG_SOC_SP7350)
-static bool remap;
+static bool remap = true;
#endif
struct vb2_dc_buf {
struct device *dev;
Temporary modification
Execute the following command before running the SNNF demo.
root@ubuntu:/snnf_demo_release# echo 1 > /sys/module/videobuf2_dma_contig/parameters/remap
USB
USB Camera supports USB 2.0 and USB 3.0. If you want to use USB 3.0, Set the jump cap in the below figure to the OFF state.
Display
SNNF demo requires a display screen by default. If you do not connect the display screen, the program will run incorrectly
The display screen supports MIPI or HDMI connection, and the currently supported MIPI display screen is the official 7-inch display screen of Raspberry Pi.
MIPI and HDMI displays cannot be used simultaneously. The specific switching method is as follows:
Switch to MIPI
Set the jump cap in the above figure to the ON state and unplug the HDMI cable.
Switch to HDMI
Set the jump cap in the above figure to OFF, power off the Panel connected to MIPI, and plug in the HDMI cable.
Source code
Please get the SNNF Demo V1.0.0 release source code here.
Folder structure
dependency_libraries: the library that snnf_demo depends on.
demo_assist
face_match
ffmpeg-4.4.2-prebuilt
freetype-2.12.1
libdrm-2.4.100-prebuilt
libpng-1.6.37
lvgl-9.1.0-prebuilt
opencv-4.9.0-prebuilt
snnf_release
vsi_lib
yuvconvert
snnf_demo_src：demo source code.
src
menu: code related to UI.
nn: sample code for SNNF and code for processing the NN results.
stream: reading video stream and displaying NN results.
makefile
out: the generation path of the snnf_demo program.
bin: snnf_demo, Prebuild sample programs that can run on the c3v Linux platform.
snnf_demo_env.sh：setup environment variable.
How to build SNNF Demo
Compile on C3V platform
Copy the release folder to C3V Linux；
root@ubuntu:/snnf_demo_release# ls -al total 24 drwxr-xr-x 5 10860 11400 4096 Nov 7 11:30 . drwxr-xr-x 4 root root 4096 Nov 7 11:17 .. drwxr-xr-x 3 10860 11400 4096 Nov 7 10:52 bin drwxr-xr-x 13 10860 11400 4096 Nov 7 10:54 dependency_libraries -rw-r--r-- 1 10860 11400 1887 Nov 7 11:30 snnf_demo_env.sh drwxr-xr-x 5 10860 11400 4096 Nov 7 12:09 snnf_demo_src
cd snnf_demo_src
root@ubuntu:/snnf_demo_release/snnf_demo_src# ls -al total 80 drwxr-xr-x 5 10860 11400 4096 Nov 7 12:09 . drwxr-xr-x 5 10860 11400 4096 Nov 7 11:30 .. -rw-r--r-- 1 10860 11400 6770 Nov 7 11:00 main.cpp -rw-r--r-- 1 root root 40776 Nov 7 12:09 main.o -rw-r--r-- 1 10860 11400 4653 Nov 7 11:00 makefile drwxr-xr-x 2 10860 11400 4096 Nov 7 12:09 out drwxr-xr-x 5 10860 11400 4096 Nov 7 10:53 snnf_demo -rw-r--r-- 1 10860 11400 1803 Nov 7 11:00 snnf_demo_env.sh drwxr-xr-x 5 10860 11400 4096 Nov 7 10:44 src
Ensure that "CROSS_COMPILE" in the makefile is set to "NO"
PLATFORM_ROOT = ../../../../../../
PROJECT_ROOT = ../
OUT_DIR = out
CROSS_COMPILE := NO
ifeq ($(CROSS_COMPILE), YES)
###config toolchain
# TOOLCHAIN_PREFIX = $(PLATFORM_ROOT)/crossgcc/gcc-arm-9.2-2019.12-x86_64-aarch64-none-linux-gnu/bin/aarch64-none-linux-gnu-
include $(PLATFORM_ROOT)/crossgcc/toolchain.config
TOOLCHAIN_PREFIX=$(TOOLCHAIN_AARCH64_PATH)/bin/$(TOOLCHAIN_AARCH64_PREFIX)-
CC = ${TOOLCHAIN_PREFIX}gcc
CXX = ${TOOLCHAIN_PREFIX}g++
else
CC = gcc
CXX = g++
endif
Make
Run snnf_demo, please refer to How to run SNNF Demo.
Cross-compile SNNF Demo
Copy the release folder to Cross-compile Linux；
root@ubuntu:/snnf_demo_release# ls -al total 24 drwxr-xr-x 5 10860 11400 4096 Nov 7 11:30 . drwxr-xr-x 4 root root 4096 Nov 7 11:17 .. drwxr-xr-x 3 10860 11400 4096 Nov 7 10:52 bin drwxr-xr-x 13 10860 11400 4096 Nov 7 10:54 dependency_libraries -rw-r--r-- 1 10860 11400 1887 Nov 7 11:30 snnf_demo_env.sh drwxr-xr-x 5 10860 11400 4096 Nov 7 12:09 snnf_demo_src
cd snnf_demo_src
root@ubuntu:/snnf_demo_release/snnf_demo_src# ls -al total 80 drwxr-xr-x 5 10860 11400 4096 Nov 7 12:09 . drwxr-xr-x 5 10860 11400 4096 Nov 7 11:30 .. -rw-r--r-- 1 10860 11400 6770 Nov 7 11:00 main.cpp -rw-r--r-- 1 root root 40776 Nov 7 12:09 main.o -rw-r--r-- 1 10860 11400 4653 Nov 7 11:00 makefile drwxr-xr-x 2 10860 11400 4096 Nov 7 12:09 out drwxr-xr-x 5 10860 11400 4096 Nov 7 10:53 snnf_demo -rw-r--r-- 1 10860 11400 1803 Nov 7 11:00 snnf_demo_env.sh drwxr-xr-x 5 10860 11400 4096 Nov 7 10:44 src
Ensure that "CROSS_COMPILE" in the makefile is set to "YES"，and modify the toolchain path("TOOLCHAIN_PREFIX") in the makefile
PLATFORM_ROOT = ../../../../../../
PROJECT_ROOT = ../
OUT_DIR = out
CROSS_COMPILE := YES
ifeq ($(CROSS_COMPILE), YES)
###config toolchain
# TOOLCHAIN_PREFIX = $(PLATFORM_ROOT)/crossgcc/gcc-arm-9.2-2019.12-x86_64-aarch64-none-linux-gnu/bin/aarch64-none-linux-gnu-
include $(PLATFORM_ROOT)/crossgcc/toolchain.config
TOOLCHAIN_PREFIX=$(TOOLCHAIN_AARCH64_PATH)/bin/$(TOOLCHAIN_AARCH64_PREFIX)-
CC = ${TOOLCHAIN_PREFIX}gcc
CXX = ${TOOLCHAIN_PREFIX}g++
else
CC = gcc
CXX = g++
endif
make
Copy the newly compiled snnf_demo program and the folder named "dependency_libraries" from the snnf_demo_delease folder to C3V Linux.
/snnf_demo_release# cp snnf_demo_src/out/snnf_demo ==> <C3V Platform>/snnf_demo_release /snnf_demo_release# cp snnf_demo_env.sh ==> <C3V Platform>/snnf_demo_release /snnf_demo_release# cp dependency_libraries ==> <C3V Platform>/snnf_demo_release
Run snnf_demo, please refer to How to run SNNF Demo.
Setup the running environment
Copy the newly compiled snnf_demo program and the folder named "dependency_libraries" from the snnf_demo_release folder to C3V Linux.
/snnf_demo_release# cp snnf_demo_src/out/snnf_demo ==> <C3V Platform>/snnf_demo_release /snnf_demo_release# cp snnf_demo_env.sh ==> <C3V Platform>/snnf_demo_release /snnf_demo_release# cp dependency_libraries ==> <C3V Platform>/snnf_demo_release
Copy according to the following directory structure.
root@ubuntu:/snnf_demo_release# ls -al total 24 drwxr-xr-x 5 10860 11400 4096 Nov 7 11:30 . drwxr-xr-x 4 root root 4096 Nov 7 11:17 .. -rwxr-xr-x 1 10860 11400 675448 Nov 7 10:58 snnf_demo drwxr-xr-x 13 10860 11400 4096 Nov 7 10:54 dependency_libraries -rw-r--r-- 1 10860 11400 1887 Nov 7 11:30 snnf_demo_env.sh root@ubuntu:/snnf_demo_release# ls -al dependency_libraries/ total 52 drwxr-xr-x 13 10860 11400 4096 Nov 7 10:54 . drwxr-xr-x 5 10860 11400 4096 Nov 7 11:30 .. drwxr-xr-x 5 10860 11400 4096 Nov 7 10:41 demo_assist drwxr-xr-x 4 10860 11400 4096 Nov 7 10:41 face_match drwxr-xr-x 3 10860 11400 4096 Nov 7 10:41 ffmpeg-4.4.2-prebuilt drwxr-xr-x 3 10860 11400 4096 Nov 7 10:41 freetype-2.12.1 drwxr-xr-x 4 10860 11400 4096 Nov 7 10:41 libdrm-2.4.100-prebuilt drwxr-xr-x 3 10860 11400 4096 Nov 7 10:41 libpng-1.6.37 drwxr-xr-x 4 10860 11400 4096 Nov 7 10:41 lvgl-9.1.0-prebuilt drwxr-xr-x 3 10860 11400 4096 Nov 7 10:41 opencv-4.9.0-prebuilt drwxr-xr-x 8 10860 11400 4096 Nov 7 10:41 snnf_release drwxr-xr-x 2 10860 11400 4096 Nov 7 10:41 vsi_lib drwxr-xr-x 2 10860 11400 4096 Nov 7 10:41 yuvconvert
Copy the resource files to C3V Linux.
The path of resource files：dependency_libraries/snnf_release/resource
#cp dependency_libraries/snnf_release/resource/* ==> <C3V Platform>/etc/snnf/
root@ubuntu:/snnf_demo_release# mkdir -p /etc/snnf root@ubuntu:/snnf_demo_release# cp dependency_libraries/snnf_release/resource/* /etc/snnf -rf root@ubuntu:/snnf_demo_release# ls -l /etc/snnf/ total 20 drwxr-xr-x 2 root root 4096 Nov 6 15:42 config. drwxr-xr-x 2 root root 4096 Nov 6 15:42 font drwxr-xr-x 2 root root 4096 Nov 6 15:43 image drwxr-xr-x 2 root root 4096 Nov 6 15:44 model drwxr-xr-x 2 root root 4096 Nov 6 15:44 video
Setup environment variable(Just need to set it once)
Switch to the directory where the dependency_libraries are located, then setup environment variable.
root@ubuntu:/snnf_demo_release/snnf_demo_src#cd ../ root@ubuntu:/snnf_demo_release/# ls -al total 24 drwxr-xr-x 5 10860 11400 4096 Nov 7 11:30 . drwxr-xr-x 4 root root 4096 Nov 7 11:17 .. drwxr-xr-x 3 10860 11400 4096 Nov 7 10:52 bin -rwxr-xr-x 1 10860 11400 675448 Nov 7 10:58 snnf_demo drwxr-xr-x 13 10860 11400 4096 Nov 7 10:54 dependency_libraries -rw-r--r-- 1 10860 11400 1887 Nov 7 11:30 snnf_demo_env.sh drwxr-xr-x 5 10860 11400 4096 Nov 7 12:09 snnf_demo_src root@ubuntu:/home/app/snnf_demo_release/#source snnf_demo_env.sh
Turn off Display Manager Service (This step is only required for Ubuntu XFCE)
The status of lightdm service enabled is as follows
Temporary stop
sunplus@ubuntu:~$ sudo systemctl stop lightdm
Permanently Closed
sunplus@ubuntu:~$ sudo systemctl disable lightdm sunplus@ubuntu:~$ sudo systemctl daemon-reload
Before running, please ensure that the account you are logged into has root privileges. If you are logging in with a non-root account, please execute the following command before running the demonstration program.
sunplus@ubuntu:/snnf_demo_release$ sudo -s root@ubuntu:/snnf_demo_release#
How to run SNNF Demo
Before running snnf_demo, please refer to Setup the running environment.
Run snnf_demo.
root@ubuntu:/snnf_demo_release# ./snnf_demo -h Usage: ./snnf_demo [options] Options: -h, --help Print this help message and exit -v, --video ARG Specify the video file or device (default: /dev/video0, e.g., /dev/video40, /mnt/test.mp4) -f, --format ARG Specify the video capture format (default: YUYV, only YUYV, UYVY, YUY2 are supported) -s, --size ARG Specify the video capture size (default: 640x480, e.g., 1920x1080, 1280x720) -r, --framerate ARG Specify the video capture frame rate (default: 30)
Obtaining input data through the camera
Use default param
root@ubuntu:/snnf_demo_release# ./snnf_demo
Set the video size/fps/YUV format by cmd.
root@ubuntu:/snnf_demo_release# ./snnf_demo -v /dev/video40 -s 1280x720 -f UYVY -r 30
How to get the format supported by the camera.
root@ubuntu:/snnf_demo_release# v4l2-ctl --list-formats-ext -d /dev/video40
Obtaining input data through the video file
root@ubuntu:/snnf_demo_release# ./snnf_demo -v /etc/snnf/video/humanCount.mp4
See the demo's effects please refer to SNNF Demo Introduction.