Full duplex asynchronous serial communication UART controller IP design

1 Design Brief

UART is short for Universal Asynchronous Receiver and Transmitter. Used for communication between serial input and serial output devices. Serial transmission comes at the cost of speed, in exchange for a reduction in cost and complexity of wiring. UART provides synchronization of serial asynchronous received data, parallel-to-serial and serial-to-parallel data conversion of the transmitter and receiver, for digital systems that need to convert serial data streams to parallel data, these functions Is essential. Synchronization of the serial data stream is achieved by adding start and stop bits to the transmitted data to form a data character. Data integrity is achieved by appending a parity bit to the data character, which is provided by the receiver Check this parity bit to check whether there is any transmission bit error. It is mainly composed of data bus interface, control logic, baud rate generator, sending part and receiving part.

1.1 Protocol

The communication protocol is the regulation of the data transmission method, including the definition of the data format and the definition of the data bits. Both parties must follow a unified communication protocol. The following is the transmission format of character data specified by the asynchronous serial communication protocol. In asynchronous communication, data is transmitted frame by frame (including a character code or a byte of data), and the data format of each frame is shown in the following figure

In the frame format, a character is composed of four parts: start bit, data bit, parity bit, and stop bit.

(1)、Start bit

The start bit (low level "0") occupies only one bit and informs the receiving device that a character to be received starts to arrive. Logic 1 state when no data is being transmitted on the communication line. When the sending device wants to send a character data, first add a logic 0 signal, this logic low level is the start bit, the receiving end continuously detects the state of the line, the receiving device detects this logic low level and starts Ready to accept data bit signals. The start bit of the character is also used to synchronize the clock of the receiving end to ensure that the subsequent reception can be performed correctly. The start bit enables the device to synchronize, and both parties must coordinate the synchronization before transmitting the data bit.

(2)、Data bit

The start bit is immediately followed by the data bit, which can be 5, 6, 7, or 8 bits. When the receiving device receives the start bit, it immediately receives the data bit. These data bits are received into the shift register and constitute the transmitted data characters. In the transmission of character data, the data bits are sent from the least significant bit and are sequentially converted into data in the receiving device.

(3)、Parity bit

After the data bits are sent, parity bits can be sent. The parity bit only occupies one bit, and the parity bit can be omitted, or this bit can be omitted, or this bit can also be used to determine the nature of the information represented by the characters in this frame (address / data, etc.) Parity check belongs to limited error detection, and both parties in communication must agree on a consistent parity check method. If you select even parity, the number of logic 1s that make up the data bits and parity bits must be even; if you select odd parity, then the number of logic 1s must be odd.

(4)、Stop bit convention

The stop bit is sent after the parity bit or data bit (when there is no parity check). The stop bit is the end mark of a character data, which can be a high level of 1, 5, or 2 bits. After receiving the stop bit, the receiving end indicates that the previous character has been transmitted, and at the same time, it is also ready to receive the next character. If it receives 0 again, the new character begins to transmit. If the stop bit is not followed by a character, the line level is kept high ("1"), which is the idle bit. After the receiving device receives the stop bit, the logic 1 state is restored on the communication line until the start bit of the next character data arrives.

(5)、Baud rate setting

All bit signals transmitted on the communication line maintain a consistent signal duration, and the signal duration of each bit is determined by the data transmission speed, that is, measured by how many binary bits per second, this speed is called the baud rate. If the data is transmitted on the communication line with 300 binary bits per second, the transmission speed is 300 baud, which is usually recorded as 300 b/s.

(6)、Handshake signal agreement

When the computer and modem exchange data, they often use some signal lines as a prerequisite for exchanging data. When the conditions are met, the data is allowed to be transmitted; when the conditions are not met, they are in a waiting state and wait until the signal that allows data transmission occurs. Data transmission begins again.

1.2 Serial-to-parallel conversion

Serial communication is to convert the parallel data to be transmitted inside the computer into serial data and transmit it through a communication line; then convert the received serial data into parallel data and send it to the computer. Before the computer serially sends data, the parallel data inside the computer is sent to the shift register and shifted out bit by bit, converting the parallel data into serial data. As shown below

When receiving data, the serial data from the communication line is sent to the shift register, and after being shifted and saved to 8 bits, it is sent to the computer in parallel

1.3 Data sampling

When the receiver receives data, the internal clock frequency of the UART is often higher than the external data input frequency. When the receiver starts to receive the signal, if the frequency of the internal clock is close to or less than the external data transmission frequency, when the receiver receives data, it is likely that the data will not be collected at the edge of data sampling, or the wrong data will be collected. The sampling frequency can be set to 8 times, 16 times the external data transmission frequency. The UART uses 16 times the external clock frequency, and the sampled waveforms are as follows:

In this example, through the research of the UART bus protocol, the UART Controller IP is designed to familiarize with the design and verification of the UART IP core

2 Design specifications

l Support AMBA APB2.0 BUS interface.

l Support 5/6/7/8 bits data (packet) transmit and receive.

l Support odd, even or none parity bit generation and declaration.

l Support 1, 1.5 or 2 stop bits generation and declaration.

l Support baud rate configuration (4800bps, 9600bps, 38400bps and 115200bps).

l Support 4 types depth RX FIFO and TX FIFO.

l Support software reset and enable.

l Support polling status – FIFO full and empty, parity check error, stop bit check error.

l Programmable interrupt enable control.

l Support the SW write clear the interrupt.

.

3 I/O Ports Description

3.1 APB Register Bus Interface

Name	Direction	Width	Description
PSEL	Input	1	APB Bus Selected Active high to select CTRL group registers.
PWRITE	Input	1	APB Bus Write Enable Active high to enable register bus write operation. Active low to enable register bus read operation.
PENABLE	Input	1	APB Bus Enable Active high to select CTRL group registers.
PWDATA	Input	32	APB Write Data Bus 32 bit data with [31] is most significant bit.
PADDR	Input	5	APB Bus Address 5 bit address bus with [4] is most significant bit.
PRDATA	Output	32	APB Read Data Bus Register read data bus, [31] is most significant bit. Valid when SL_APB_ACK is active.

3.2 Interrupt Line

Name

Direction

Width

Description

INT_B

Output

1

Interrupt

Low active. When finished a operation, INT_B will be active, such as received a packet or error case happened.

3.3 System Clock and Reset

Name

Direction

Width

Description

SYSCLK

Input

1

System Clock

Free running clock, all registers must be synchronous with SYSCLK.

RST_B

Input

1

System Reset

Low active. When this pin is asserted, all flip-flops must be reset to their default value.

3.4 UART interface

Name	Direction	Width	Description
RX	Input	1	Serial Data input
TX	output	1	Serial Data output

4 Registers File

4.1 Registers List

Address	Name	Access	Description
5’h00	LCR	RW	Line Control Register
5’h01	SER	RW	Software Enable Register
5’h02	BAUD_CNT	RW	Baud-rate Configuration Register
5’h03	LSR	RW	Line State Register
5’h04	RX_FIFO	RO	RX FIFO Register
5’h05	TX_FIFO	RW	TX FIFO Register

4.2 Line Configuration Register (LCR, Addr = 5’h0)

Default value: 0x0000_0000

Register Bits	Name	Function Description
1:0	WORD_SEL	Word Length Select of the UART 00 : 8 bit data transmit and receive 01 : 7 bit data transmit and receive 10 : 6 bit data transmit and receive 11 : 5 bit data transmit and receive
3:2	STOP_SEL	Stop Bit Length of the UART 00 : 1 cycle stop bit 01 : 1.5 cycle stop bit 10 : 2 cycle stop bit Default : 1 cycle stop bit
5:4	PTY_SEL	Parity Select of the UART 00 : even parity 01 : odd parity 10 : no parity Default : even parity
31:6	RSV	Reserved

4.3 Software Enable Register (SER, Addr = 5’h1)

Default Value: 0x0000_003f

Register Bits	Name	Function Description
0	RX_DONE_EN	Data Ready Interrupt Enable Low active, when this bit is 1, Data Ready will not assert interrupt.
1	TX_DONE_EN	Transmitted Complete Interrupt Enable Low active, when this bit is 1, Transmitted Complete will not assert interrupt.
2	PTY_ERR_EN	Parity Error Interrupt Enable Low active, when this bit is 1, Parity Error will not assert interrupt.
3	STOP_ERR_EN	Stop Bit Error Interrupt Enable Low active, when this bit is 1, Stop Bit Error will not assert interrupt.
4	RX_FULL_EN	RX FIFO Full interrupt Enable Low active, when this bit is 1, TRX FIFO full will not assert interrupt.
5	TX_EMPTY_EN	TX FIFO Empty interrupt Enable Low active, when this bit is 1, TX FIFO empty will not assert interrupt.
6	SW_RST	Soft Reset UART High active , the UART will reset when Master writing 1 to this bit
7	RX_EN	Receiver FSM Stop Low active , the Receiver will not work when this bit is 1
8	TX_EN	Transmitter FSM Stop Low active , the Transmitter will not work when this bit is 1
31:9	RSV	Reserved

4.4 Baud-rate Configuration Register (BAUD_CNT, Addr = 5’h2)

Default Value: 0x0000_0000

Register Bits

Name

Function Description

31:0

BAUD_CNT

Baud Rate configure data

Store the count value of baud rate generation

4.5 Line State Register (LSR, Addr = 5’h3)

Default value: 0x0000_0000

Register Bits	Name	Function Description
0	RX_DONE	Data Ready High active, the flag of the interrupt that Received a complete packet. The interrupt will be cleaned when this bit is written 0 by master.
1	TX_DONE	Transmitted Data Complete High active, the flag of the interrupt that Transmitted a complete packet. The interrupt will be cleaned when this bit is written 0 by master.
2	PTY_ERR	Parity Error High active. The interrupt flag that Parity error. The interrupt will be cleaned when this bit is written 0 by master.
3	STOP_ERR	Stop Bit Error High active. The interrupt flag that Stop bit error. The interrupt will be cleaned when this bit is written 0 by master.
4	RX_FULL	RX FIFO Full High active. The interrupt flag that RX FIFO full. The interrupt will be cleaned when master reads out a data once.
5	RX_EMPTY	RX FIFO Empty High active. The flag that the RX FIFO empty
6	TX_FULL	TX FIFO Full High active. The flag that the TX FIFO full
7	TX_EMPTY	TX FIFO Empty High active. The flag of the interrupt that TX FIFO empty. The interrupt will be cleaned when master writes a data once.
31:8	RSV	Reserved

4.6 RX FIFO Register (RX_FIFO, Addr = 5’h4)

Default Value: 0x00

Register Bits

Name

Function Description

7:0

RX_FIFO

Read Data Buffer

The depth is 4.

Store the data written to Receiver buffer register.

4.7 TX FIFO Register (TX_FIFO, Addr =5’h5)

Default Value: 0x00

Register Bits

Name

Function Description

7:0

TX_FIFO

Write Data Buffer

The depth is 4.

Store the data written to Transmitter buffer register.

5 Functional Description

5.1 UART Structure

Interface model: communicate with CPU, configure the UART.

FIFO: store data which will be transmitted or received

Transmit/Receive register: transmit or receive the data stored in the FIFO.

Baud rate occur: occur the clock for transmitter and receiver

5.2 UART Receiver FSM

Current State	Function	Next Status	Jump Condition
IDLE	Wait start signal.	SHIFT	Start bit detected right and receiver buffer register isn’t full
IDLE	Wait start signal.	IDLE	RX_EN enable or start bit not detected
SHIFT	Receive data	STOP	Last data bit and parity disable
		PARITY	Last data bit and parity enable
		SHIFT	Not last data bit
PARITY	Odd/even parity check	STOP	Parity check done
STOP	Stop bit check	IDLE	Check right, then jump to IDLE Or check right wrong ,INT_B enable, then jump to IDLE

5.3 UART Transmitter FSM

Current State	Function	Next Status	Jump Condition
IDLE	Wait for transmitting	START	TX_FIFO is not empty
IDLE	Wait for transmitting	IDLE	TX_FIFO is empty or TX_EN enable
START	Transmit start bit	SHIFT	Transmit done
SHIFT	Transmit data	STOP_1BIT	Last data bit and parity disable
		PARITY	Last data bit and parity enable
		SHIFT	Not last data bit
PARITY	Parity bit	STOP_1BIT	Finished the parity configuration
STOP_1BIT	1 stop bit	START	1.5/2 stop bit disable
		STOP_HALFBIT	1.5 stop bit enable
		STOP_2BIT	2 stop bit enable
STOP_HALFBIT	1.5 stop bit	START	Finished the stop bit configuration
STOP_2BIT	2 stop bit	START	Finished the stop bit configuration

5.4 FIFO

FIFO is very important to this design as all data are transferred by it. Following is the 2-pointer FIFO

It is a 4X8-bit FIFO, so the width of both write pointer (WP) and read pointer (RP) are 3 bits. Read data once, RP adds one, while write data once, WP adds one.

When write, first write data, then move the WP pointer; when read, first read data, then move the RP pointer.

When WP = RP indicates FIFO is empty.

When WP [2] = (~RP [2]) and WP [1:0] = RP [1:0] shows this is a full FIFO

5.5 Timing Figures

Receive the serial data from RX

Transmit the serial data to TX

6 SOC integration

6.1 Hardware platform implementation of UART controller IP design experiment project

The UART controller IP core design is the AMBA APB bus interface, and our FBIO Wrapper is the AMBA AXI bus interface, which cannot be directly connected together, and requires an AXI2ABP Bridge to connect;

This experiment uses the FPGA daughter board supporting the Plus1 7021 SOC practice platform to complete the relevant experiment. The experiment is carried out in loopback mode, which is to connect the TX and RX of the UART controller IP core design; The development tool of FPGA daughter board uses XILINX's Vivado integrated development environment (version number is 2018.3); in order to facilitate the connection of the user's own verification IP to the SOC system for verification, this experiment provides the corresponding design reference basic files, as follows

The corresponding connection between the design case and the pin connection of the SP7021 motherboard and FPGA daughter board is shown in the following table: 1: U20B on the main board is connected to J2 of the FPGA daughter board (Pin pin corresponding, such as 1-51 ...), providing the data transmission channel between the Plus1 main chip on the main board and the FPGA

Design Demo	FPGA daughter board			SP7021 mother board
uart_apb	J2		U1E	U20B
Top Port Name	Schematic Name		FPGA I/O	Schematic Name
	1	GND		51	GND
	2	GND		52	GND
FPGA_PAD[0]	3	B34_L24_N	T8	53	FBIO_PAD_0
FPGA_PAD[43]	4	B34_L24_P	R8	54	FBIO_PAD_1
	5	VIN		55	VCC(3.3V)
	6	VCCIO34		56	VCC(3.3V)
FPGA_PAD[1]	7	B34_L21_N	V9	57	FBIO_PAD_2
FPGA_PAD[42]	8	B34_L21_P	U9	58	FBIO_PAD_3
FPGA_PAD[2]	9	B34_L18_N	N6	59	FBIO_PAD_4
FPGA_PAD[41]	10	B34_L18_P	M6	60	FBIO_PAD_5
FPGA_PAD[3]	11	B34_L22_N	U6	61	FBIO_PAD_6
FPGA_PAD[40]	12	B34_L22_P	U7	62	FBIO_PAD_7
FPGA_PAD[4]	13	B34_L20_N	V6	63	FBIO_PAD_8
FPGA_PAD[39]	14	B34_L20_P	V7	64	FBIO_PAD_9
FPGA_PAD[5]	15	B34_L23_N	T6	65	FBIO_PAD_10
FPGA_PAD[38]	16	B34_L23_P	R7	66	FBIO_PAD_11
FPGA_PAD[6]	17	B34_L10_N	V4	67	FBIO_PAD_12
FPGA_PAD[37]	18	B34_L10_P	V5	68	FBIO_PAD_13
FPGA_PAD[7]	19	B34_L19_P	R6	69	FBIO_PAD_14
FPGA_PAD[36]	20	B34_L19_N	R5	70	FBIO_PAD_15
FPGA_PAD[8]	21	B34_L8_P	U4	71	FBIO_PAD_16
FPGA_PAD[35]	22	B34_L8_N	U3	72	FBIO_TCLK
FPGA_PAD[9]	23	B34_L9_N	V2	73	FBIO_RCLK
FPGA_PAD[34]	24	B34_L9_P	U2	74	FBIO_PAD_17
FPGA_PAD[10]	25	B34_L7_N	V1	75	FBIO_PAD_18
FPGA_PAD[33]	26	B34_L7_P	U1	76	FBIO_PAD_19
FPGA_PAD[11]	27	B34_L13_P	N5	77	FBIO_PAD_20
FPGA_PAD[32]	28	B34_L13_N	P5	78	FBIO_PAD_21
FPGA_PAD[12]	29	B34_L12_P	T5	79	FBIO_PAD_22
FPGA_PAD[31]	30	B34_L12_N	T4	80	FBIO_PAD_23
FPGA_PAD[13]	31	B34_L11_N	T3	81	FBIO_PAD_24
FPGA_PAD[30]	32	B34_L11_P	R3	82	FBIO_PAD_25
FPGA_PAD[29]	33	B34_L14_P	P4	83	FBIO_PAD_26
FPGA_PAD[28]	34	B34_L14_N	P3	84	FBIO_PAD_27
FPGA_PAD[14]	35	B34_L16_N	N4	85	FBIO_PAD_28
FPGA_PAD[27]	36	B34_L16_P	M4	86	FBIO_PAD_29
FPGA_PAD[15]	37	B34_L17_N	T1	87	FBIO_PAD_30
FPGA_PAD[26]	38	B34_L17_P	R1	88	FBIO_PAD_31
FPGA_PAD[16]	39	B34_L15_N	R2	89	FBIO_PAD_32
FPGA_PAD[25]	40	B34_L15_P	P2	90	FBIO_PAD_33
FPGA_PAD[17]	41	B34_L3_N	N1	91	FBIO_PAD_34
FPGA_PAD[24]	42	B34_L3_P	N2	92	FBIO_PAD_35
FPGA_PAD[18]	43	B34_L1_N	M1	93	FBIO_PAD_RSTB
FPGA_PAD[23]	44	B34_L1_P	L1	94	EXT0_INT
	45	VCCIO34		95	VCC(3.3V)
	46	VIN		96	VCC(3.3V)
FPGA_PAD[19]	47	B34_L4_P	M3	97	EXT1_INT
FPGA_PAD[20]	48	B34_L4_N	M2	98
	49	GND		99	GND
	50	GND		100	GND

2: U20A on the motherboard is connected to J1 of the FPGA daughter board (Pin pins correspond to one, such as 1-1 ...), and the 42 pin IO (3.3v) of FPGA Bank 35 is extended via J17 for users to use

Design Demo	FPGA daughter board			SP7021 mother board
uart_apb	J1		U1F	U20A		J17
Top Port Name	Schematic Name		FPGA I/O	Schematic Name		Schematic Name
	1	GND		1	GND	3	GND
	2	GND		2	GND	4	GND
FPGA_TX	3	B35_L23_N	K1	3	B35_L23_N	5	B35_L23_N
	4	B35_L23_P	K2	4	B35_L23_P	6	B35_L23_P
	5	VIN		5	VIN	1	VCC
	6	VCCIO35		6	VCCIO35	2	VCC
FPGA_RX	7	B35_L15_N	G2	7	B35_L15_N	7	B35_L15_N
	8	B35_L15_P	H2	8	B35_L15_P	8	B35_L15_P
	9	B35_L13_N	F3	9	B35_L13_N	9	B35_L13_N
	10	B35_L13_P	F4	10	B35_L13_P	10	B35_L13_P
	11	B35_L12_N	D3	11	B35_L12_N	11	B35_L12_N
	12	B35_L12_P	E3	12	B35_L12_P	12	B35_L12_P
	13	B35_L22_P	J3	13	B35_L22_P	13	B35_L22_P
	14	B35_L22_N	J2	14	B35_L22_N	14	B35_L22_N
	15	B35_L17_N	G1	15	B35_L17_N	15	B35_L17_N
	16	B35_L17_P	H1	16	B35_L17_P	16	B35_L17_P
	17	B35_L18_N	E1	17	B35_L18_N	17	B35_L18_N
	18	B35_L18_P	F1	18	B35_L18_P	18	B35_L18_P
	19	B35_L14_N	D2	19	B35_L14_N	19	B35_L14_N
	20	B35_L14_P	E2	20	B35_L14_P	20	B35_L14_P
	21	B35_L16_P	C2	21	B35_L16_P	21	B35_L16_P
	22	B35_L16_N	C1	22	B35_L16_N	22	B35_L16_N
	23	B35_L9_N	A1	23	B35_L9_N	23	B35_L9_N
	24	B35_L9_P	B1	24	B35_L9_P	24	B35_L9_P
	25	B35_L10_P	B3	25	B35_L10_P	25	B35_L10_P
	26	B35_L10_N	B2	26	B35_L10_N	26	B35_L10_N
	27	B35_L8_N	A3	27	B35_L8_N	27	B35_L8_N
	28	B35_L8_P	A4	28	B35_L8_P	28	B35_L8_P
	29	B35_L11_N	D4	29	B35_L11_N	29	B35_L11_N
	30	B35_L11_P	D5	30	B35_L11_P	30	B35_L11_P
	31	B35_L3_N	A5	31	B35_L3_N	31	B35_L3_N
	32	B35_L3_P	A6	32	B35_L3_P	32	B35_L3_P
	33	B35_L2_N	B6	33	B35_L2_N	33	B35_L2_N
	34	B35_L2_P	B7	34	B35_L2_P	34	B35_L2_P
	35	B35_L7_N	B4	35	B35_L7_N	35	B35_L7_N
	36	B35_L7_P	C4	36	B35_L7_P	36	B35_L7_P
	37	B35_L1_N	C5	37	B35_L1_N	37	B35_L1_N
	38	B35_L1_P	C6	38	B35_L1_P	38	B35_L1_P
	39	B35_L5_N	E5	39	B35_L5_N	39	B35_L5_N
	40	B35_L5_P	E6	40	B35_L5_P	40	B35_L5_P
	41	B35_L6_N	D7	41	B35_L6_N	41	B35_L6_N
	42	B35_L6_P	E7	42	B35_L6_P	42	B35_L6_P
	43	B35_L19_P	G6	43	B35_L19_P	43	B35_L19_P
	44	B35_L19_N	F6	44	B35_L19_N	44	B35_L19_N
	45	VCCIO35		45	VCCIO35	49	VCC
	46	VIN		46	VIN	50	VCC
	47	B35_L4_N	C7	47	B35_L4_N	45	B35_L4_N
	48	B35_L4_P	D8	48	B35_L4_P	46	B35_L4_P
	49	GND		49	GND	47	GND
	50	GND		50	GND	48	GND

6.2 Implementation of System Software Platform for UART Controller IP Design Experiment Project

In the IDE environment, as shown below, select the sp7021 project name, click the right mouse button and select Copy in the pop-up menu

Next, select the sp7021 project name again

Click the right mouse button and select Paste in the pop-up menu, the following picture appears

Fill in the uart_apb in the Project name box to complete the establishment of the uart_apb project name and directory, as shown below

Next, you need to copy all the files and folders under the installation directory \SP7021\example\uart_apb to the uart_apb project directory built above (the path is: installation directory \SP7021\workspace\uart_apb\), the file with the same name is selected to be overwritten, so that the UART The program codes main.c; uart.c; uart.h required for the IP design practice of the controller are placed in the following paths:

1） In the install directory \SP7021\workspace\uart_apb\main.c

2） In the install directory \SP7021\workspace\uart_apb\testapi\util\uart.c

3） In the install directory \SP7021\workspace\uart_apb\include\util\uart.h

Finally, as shown in the figure below, the mouse selects the red box 1, then clicks the right mouse button to appear the drop-down menu, and then selects the red box 2, refresh the copy action just now, so that the file just copied can be displayed in the IDE environment

main.c

int main(void)

{

printf("Build @%s, %s\n", __DATE__, __TIME__);

hw_init();

sys_init();

fbio_init();

uart_ctl();

disp_hdmi_init();

uart_interrupt_init(); /*uart interrupt configure */

sp_interrupt_setup(); /* system interrupt manager module init */

printf("UART IP test ready ");

while(1)

{

unsigned int i;

for (i = 0; i < 256; i++)

{

while(1)

{

if((uart_reg->LSR&0x20)==0x20)

{

uart_reg->SER=0x3f;

uart_reg->TX_FIFO=i;

printf("@tx_data [%d]\n", i);

uart_reg->SER=0x3e;

break;

}

Compared with the digital tube control IP experiment, the uart_ctl () function is added to complete the configuration and initialization of the UART, as explained below.

void uart_ctl()

{

uart_reg->LCR=0x20;

printf("@LCR[%x]\n", temp);

uart_reg->SER=0x3e;

printf("@SER[%x]\n", temp);

///////////////// system clock is 65.057MHz//////65057000/16/buad//////

uart_reg->BUAD_CNT=0x1A9; //9600

printf("@BUAD_CNT[%x]\n", temp);

}

Realize the configuration and initialization operation of UART control IP as follows:

uart_reg->LCR=0x20;

Set UART to 8bit data bit, 1bit stop bit, no parity bit;

uart_reg->SER=0x3e;

Set the UART interrupt to: allow interrupts to be generated after receiving data is complete; disable interrupts to be generated after data transmission is complete; prohibit stop bits from receiving data and generate interrupts when the check bit is wrong; disable interrupts when receiving data FIFO is full; Generate an interrupt;

uart_reg->BUAD_CNT=0x1A9;

Set the UART baud rate to 9600;

The following introduces while (1) loop

if((uart_reg->LSR&0x20)==0x20) : Judge that the received data FIFO is empty

uart_reg->SER=0x3f; Forbid receiving data interruption;

uart_reg->TX_FIFO=i; Send data i to TX FIFO;

uart_reg->SER=0x3e; Allow interrupt generation after receiving data

uart.c

#include "common_all.h"

#include "cache.h"

#include "sp_interrupt.h"

#define FPGA_EXT0_INT (29)

#define FPGA_EXT1_INT (30)

static unsigned int g_repeat_cnt = 0;

unsigned int rx_data;

void fpga_ext0_interrupt_control_mask(int enable)

void fpga_ext1_interrupt_control_mask(int enable)

static void fpga_ext0_isr_cfg()

static void fpga_ext1_isr_cfg()

void fpga_ext0_callback(void)

void fpga_ext1_callback(void)

void uart_interrupt_init ()

void fpga_ext1_test_init()

Compared with the LED.c of the LED control IP experiment, the structure is similar, the difference is that the interrupt handler is different, as explained below

void fpga_ext0_callback(void)

{

rx_data=uart_reg->RX_FIFO;

printf("@rx_data [%d]\n", rx_data);

uart_reg->LSR=0x0;

}

The role of this interrupt handler: take the 8bit data received by the RX FIFO; then clear the status flag bit of this interrupt, so that the serial reception and transmission experiments of 1byte data are completed.

uart.h

#ifndef __FPGAINT_H__

#define __FPGAINT_H__

#define FBIO_BASE_ADDR 0x70000000

typedef struct uart_reg_s {

unsigned long LCR;

unsigned long SER;

unsigned long BUAD_CNT;

unsigned long LSR;

unsigned long RX_FIFO;

unsigned long TX_FIFO;

} uart_reg_t;

extern uart_reg_t *uart_reg;

void uart_interrupt_init ();

void fpga_ext1_test_init();

#endif // __FPGAINT_H__

Defined UART control IP related registers

6.3 Run Program code

After compile in the Plus1 IDE environment, download to the platform and see the following information in the terminal window